Atm Error Code Lookup
Please contact the manufacturer if these error happen. 4G411 Cash remain in cash tray Reset the Machine 40011 Upper check sensor left jam Bill jam or sensor failure. Test the dispenser by completing several test dispenses. 3. Check with the processor. Use an electrical parts contact cleaner on terminals. http://msix.org/error-code/att-error-code-185.html
Reset the machine if problems persist, please contact the service provider 40044 Exit timeout Hardware failure. Remove note from the CDU delivery path. 2. D2100 Modem initialization error Check modem in diagnostics or modem test. Exchange a sensor after abnormal operating CS3 Gate detecting sensor. 6. https://www.tritonatm.com/service_and_support/error_code_lookup/index.php
Atm Error Codes List
Please contact the services provider when this error happens. 1G213 Command timing error Software error. Also check that black and white, 2 wire connector is properly connected at rear of main board. Replace the power supply or dispenser DC power if either is defective. 3. CDN0F CDU connection failure Check cables between CDU and Mainboard, remove cables (even though they may be attached) and re-connect.
- Check the transaction from the host and try again. (Check out our Hyosung ATMs for sale & our Triton ATMs for sale) Error D0054 Hyosung ATM Error Code EXPIRED
- Error Code: 132 Description: Error code reports bad doubles detect in last dispense.
- Purge the dispenser using PURGE command.
- If the error persists, replace the SPED keypad module. 206 SPED keypad could not perform a successful command within SPED_MAX_ATTEM PTS tries Status valid only for units with SPED keypad device
- Inspect main board to electronic journal communication cable for damage.
- If cash dispenser operates normally, it will pick from seven to fifteen notes from each cassette to calibrate the double detect to the document in each of the cassettes.
- Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error.
- Check a jammed note in 3 Cassette or remount it 4.
- Test the dispensing mechanism by completing several test dispenses. 4.
- Error Code: 357 Description: Dispenser data size error.
Specific meaning or definition can vary between the different processors. If the error clears, put the cash dispenser in service. 6. Clear the error. Atm Response Code 072 Replace hard disk drive 9712500Failed to copy file1.
However, actions to fill the cassette should be taken as soon as possible. Atm Error Code 3-da000(80) C00E1 NS4 dark Verify connections to NS4 sensor. If the problem persists, replace the dispensing mechanism. belts, gears, cables, or sensors).
Error Code: 145 Description: Error in reply from the electronic journal. Sbi Atm Response Code 70 Test the dispenser by completing several test dispenses. Please contact the manufacturer when this error happens. 0E214 Non defined application command Software error. Clean the dirty sensor, or replace the note transport as needed.
Atm Error Code 3-da000(80)
Check CS13 sensor (note jam and dust)2. http://www.atmdepot.com/tranax-atm-error-codes/ Loose belts can slip off rollers and block sensors. 21B15 CDU detects bills prior to dispensing This means that while the ATM was initializing it detected a blocked sensor in the Atm Error Codes List Otherwise, replace the dispenser. 2. Atm Error Code 3-da001 Check the incoming power and dispenser mechanism for proper grounding.2.
Error Code: 152 Description: Electronic journal corrupt. http://msix.org/error-code/apc-error-code-f02.html D0041 No credit account found for the CCN Code reported by host processor (Shazam). If so, work to resolve error code 151. 1. Inspect the cassette and feed path for jammed currency. Triton Error Code 244
Remove jammed notes2. Complete a live transaction. If all sensors are operation correctly, and the error persists, replace the replace the dispenser. 42 Transport error. have a peek at these guys Check CS15A Sensor Cable 3.
Clear any jammed currency. 2. Sbi Atm Response Code List Pdf Remove the dust on the CS31A and CS31B Sensors 5. Verify correct operation with a live transaction. 3.
Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends.
Call your attendant 9701102COM handle is null for EPP1. Otherwise the dispenser may require service C0030 CDU motor failure Motor speed (measured at the encoder wheel) was not within spec. Inspect the feed path for any jammed notes. Atm Error Code 68 Error Code: 358 Description: Dispenser device read error.
Error Code: 203 Description: SPED keypad is not replying to main board. Error Code: 151 Description: Electronic Journal Full. Error Code: 330(4Eh)[N] Description: Communication timeout. check my blog Recommended Action: Inspect the electronic journal to make sure is it the correct part number.
Clean dispenser and cassette. Reset the machine, if problems persist, please contact the manufacturer 5G127 Disconnect Response Software error. Remove jammed currency. 2. Carefully install the double detect module into the note qualifier.
Reset the machine if problems persist, please contact the service provider 43031 Jam at exit Bill jam or sensor failure. Clear the error. Reset the machine if problems persist, please contact the service provider 40047 Divert error Hardware failure. If resets are suspected, determine what could have caused the main board to reset.
Remove the remaining notes and foreign objects at the position of the CS4 sensor 2. D0005 Undefined network processing error Code reported by host processor. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. NOTE: Do not use metal objects to clear the jam.