Astro Spectra Error 06/10
Pin 1 RED/WHITE&GREEN PTT Pin 22 BLACK SW A+ Pin 9 BLUE/BLACK RECEIVE AUDIO Pin 23 WHITE CARRIER DETECT Pin 18 WHITE/BLACK&ORANGE/BLACK& BLACK/WHITE&GREEN/WHITE GROUND Pin 12 GREEN/BLACK TRANSMIT AUDIO (Audio level X FAIL 999 Serial number in the Memory Board and the microcomputer do not match; Radio will not function but will enter test mode. With the dual head operation should I be programming >through >the DB15 on the back of the radio?? control head. weblink
Until/unless someone comes up with the factory adjustment instructions we are all in the same boat and will have to wing it if we need to adjust it. U BLANK DISPLAY BUT TX AND BUSY LED'S LIT BRIEFLY AT POWER UP Display malfunction Replace Control Head Board V FAIL 001 Synthesizer out-of-lock condition See Synthesizer Troubleshooting W FAIL 002 Spectra's come in many frequency bandsplits, called Ranges. If your control head head is one of the older heads that use DIP construction, check out the U2 EEPROM chip. http://www.repeater-builder.com/motorola/spectra/spectra-error-codes.html
Motorola Apx 7500 Error Codes
Conn. The SIU would seem to limit the setup to 99 channels per radio, but this is not true. When connecting an A7 head to an A5 radio, all A5 functions work but the A7 only functions do not (direct mode access etc.). This radio is not capable of scanning...
- For example, a 3880196P01 is now a 3805671X02.
- May be control head failure, a radio command board failure, or a cabling failure a.
- FAIL 01/82 FLASH ROM Codeplug Checksum FATAL Reprogram the codeplug.
Replace EEPROM fromARCHIVE file if availableb. This connection is already standard on all HLN5299 Personality Boards and is built into the PC board copper traces. Put this chip back on the board and remove the second chip and do the same, labeling it too (ie. 800 C9 RIGHT). Motorola Xts2500 Fail 01/82 Next, check the radio cable and make sure it is a negative ground cable with the part number or with an ohm meter (pin A should be connected to the large
Then, you cut a whole bunch of shrink tubing and start soldering and insulating as you go. Motorola Apx Error Codes The pinout of the 15 pin accessory connector on the Spectra 900 is as follows: 1 TX Audio 2 Emerg 3 VIP out 2 (dash mount only, not used in remote To get 5khz deviation on TX, solder .003 mfd across C651. my site http://www.batlabs.com/spectra.html < -- has the meaning of the FAIL 1/90 code - scroll down http://www.repeater-builder.com/motorola/spectra/spectra-caps.html <-- excellent site on changing out the bad caps on the Spectras.
BTW, if your radio is capable of zones, you can have a scanlist for each zone... Xtl5000 Fail 01/82 Forums Search Forums Recent Posts Members Notable Members Registered Members Current Visitors Search Batboard Batboard Forum - Please go back to using batboard.batlabs.com URL. M Conventional 7Conventional B Privacy Plus 3 HHCH M Motorcycle 3 30 W 3 High Band VHF V ? Anyone know what this means?
Motorola Apx Error Codes
We can call our local radio guy but its 90 bucks for them to just look at it. https://www.manualslib.com/manual/905226/Motorola-Astro-Xtl-5000.html?page=124 FAIL 05/81 Control Head ROM Checksum Error FATAL Replace the control head. Motorola Apx 7500 Error Codes If you want to force an A9 type head, change this location to 0xCD. Motorola Xts 2500 Error Code 09/10 FATAL Send the radio to the depot; replace the daughter card. 6881096C73-O Previous page Next page 1...122123124125126 Also See for Motorola ASTRO XTL 5000 Motorola ASTRO XTL 5000 User Manual
J --- Hang-up return K --- Hang-up M --- Speaker Hi N --- Speaker Lo As with all Spectras, the audio amplifier is a direct coupled, floating type. have a peek at these guys If you find any jumper wires here, identify the J1 pin number and look them up here. Pressing enter brings up a submenu with these choices: NAME, SCAN and EXIT. This version of RSS also lets you program down to 140 MHz on the 146-174 MHz bandsplit radios. Motorola Xtl 2500 Error Codes
New Radio Modifications: If your Personality Board is an HLN4925 then you may want to consider adding a jumper wire to the solder side of this board. Display slowly shows: Service Rotate rotary mode knob once and display shows (for example): S/N 617 AWL 1288 Then display goes to the main menu system with the following main headings. Meister WA1MIK If you have documentation that shows additional device codes and/or error codes,please forward them to the e-mail address listed at the bottom of this article. http://msix.org/error-code/astro-spectra-error-09-10.html DO NOT GROUND either speaker line or permanent damage to the radio may result.
FATAL Replace the VRS. Motorola Error 9/10 This is a LED mounted under a hole in the RF board. The backup URL will remain batboard.dreamhosters.com Skip to content Search Advanced search Quick links Unanswered posts Active topics Search The team FAQ Login Register Board index General General Motorola Solutions &
When squelch setting number 2 is set, the Squelch Threshold potentiometer R213 is in exclusive control of the squelch level.
FATAL Turn the radio off, then on. Radio will function normally until a corrupted mode is accessed; then "FAIL 002" will be displayed (see below) a. I'm not sure why this menu is here as it gives one the felling that individual ZONES can be scanned thru and I don't think this is true. Motorola Xts 2500 Error Codes The HCN1066 head is a Spectra head that has rocker positions for Zone, Mode, and Volume.
NON-FATAL Turn the radio off, then on. They will be in one of three formats: ER xx/yy or ERROR xx/yy FL xx/yy or FAIL xx/yy FAIL nnn Where "xx" and "yy" will be hexadecimal characters (0-9, A-F), and The more R213 is turned clockwise (towards zero ohms), the smaller the combined resistance difference gets between squelch setting 1 and 2. this content A FAIL message is fatal and the radio will usually not work at all.
Check J1-24 (spare 1), J1-13 (spare 2) and their PC traces as they are sometimes used to feed power to the control head. All Rights Reserved, including that of paper and web publication elsewhere. This is kind of nice if you have a radio that is zone capable, then you can have a properly labeled zone rocker rather than having to use a couple of The other way to change the serial numbers (command board AND MLM) in a Spectra is to use LAB RSS and use the serial number change utility (service menu I believe).
That is, the first thing you do is disconnect power, and the last thing you do is connect power. It turns out this radio is really a Syntor X Smartnet Dual Operation radio with a HCN1032 control head (it only looks like a normal Systems 9000 control head), Systems 9000 When the clone operation is started you will most likely get a warning message that the radios features are different, tell it to proceed. Squelch setting number 3 only uses R214 and squelch setting number 4 does not use either one.
For the out of band modifications, you will want to click here. The Spectra "SP02" microprocessor is used to convert Syntor X 9000 VRS "SP01" into a Spectra "SP02" VRS. There is some duplication and redefinition of codes due to extra circuitry in the Astro Spectra radios. Spectra serial number If you want to change the serial number in your radio, here is the C source for a program that is supposed to do it.
Enter the last four digits of the radios serial number here. If you can locate the tag, it will give you the part number and revision (i.e. Service Manuals Here are a listing of the Service Manual part numbers for this series of radios: 6880102W61 -- Spectra Detailed Service Manual 6880101W33 -- Spectra Deatiled Service Manual is this Even in the Front/Rear Installation Manual, it states that there is no electrical difference between the front and rear heads, only the programming of the EEPROM (through RSS).
FATAL Replace the aux. Astro Spectra + ER 06/10 The General forum is where users can discuss any topic regarding Motorola communications equipment - hardware, software, etc. Below is a list of the available ranges for VHF and UHF. I am using astro version 8 Rss. >Both heads and cable are new and work fine...
There may be a small white tag stuck to the Personality Board with the part number on it.