Aruba Spa Fl1 Error Code
Hopefully not the beginning of a more serious problem. Is this expected? Torrance October 12, 2015 Reply My sundance cayman hot tub is not heating up the water, I am not getting any fault codes on the control panel. In both cases, the spa heater will deactivate. his comment is here
Any assistance would be helpful. The J-315 is similar to the J-325 but has more jetting for more water movement.The J-365 jacuzzi hot tub hot tub spa is a 6 person hot tub. Condition can cause injury or damage to spa and its components. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive.
Jacuzzi Error Code Fl1
Can it be something other than the filter? We finally got it together to run the power to the spa, and the display is lighting up. Click on this link for all Sundance Spas Manuals:Sundance Spa Owner ManualsSundance Spas Tech Tips:Some of the most common error codes for Sundance and some tech tips to assist you: 1.
Your filters were just clogged restricting flow through them. Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi Hot Tubs & Spas is headquartered in Chino, California. FL1 error was gone. Sundance Hot Tub Flo Error Greg Share this post Link to post Share on other sites Create an account or sign in to comment You need to be a member in order to leave a comment
Joe May 29, 2016 Reply I have a Sundance spa model Marin with an 850 PWA of year 2008. Fl1 Error Sundance Spa Do all the other functions of the tub work, jets low and hi, light? Smith Motors Clearwater Spas Coates Confer Plastics Continental Leisure Cotherm CoverValet CSD Custom Molded Products Custom Moulded Products Dakota Spas Delzone Diehl Dimension One Spas Discovery Spas Discovery Spas_1 Diversitech Corporation Ask for Mrs.
Ask an Expert Online. Balboa Hot Tub Error Codes Also put your hand on the circ pump to see if it is overly hot to the touch. Proper water flow is inhibited or flow/pressure switch may be obstructed, misaligned, or defective.Troubleshooting Steps:1. If you can let me know what model you own I may be able to send some troubleshooting tips your way.
- If the motor shaft is free wheeling you could try to replace your start capacitor.
- Press and hold the + and - btn at the same time for a few seconds it should read F1 or F2.
- To check out please select Checkout Now.
- With the circ pump on and the main pump off (Portofino Models with Circulation Pump), test switch operation with an ohmmeter meter in the continuity position, test for continuity across switch
- pump, however mine still seems to be working(no noise and water is been circulated as I can feel it from the small outlet).
- To clear the message press button D toreturn to the Main MenuPress the D button to clear the message and return to the main menu.Jacuzzi Hot Tubs J-300 Error Conditions/ Error
- Do all the other functions of the tub work, jets low and hi, light?
- Anything I can do to get rid of the error so heater will function at low speed?
- System is disabled in this event and indicates a shorted or closed flow switch when system is started up.Do not attempt to service on your own.
- FL1 or FL 2 Error CodeFL1:Flow or pressure switch not closed when pump is running.
Fl1 Error Sundance Spa
You could also leave a picture of your pump here for id purposes. http://www.spaandpoolsource.com/trouble-shooting.aspx We have replaced the flow switch, circuit board, and circuits but I can't lower the temperature. Jacuzzi Error Code Fl1 Any suggestions on what to do next. Sundance Spa Error Codes Then make sure your not in an economy mode.
But, sounds like you went through the same frustration we are. this content Not too familiar with the inner workings, but can access the main components at the primary access, where the circuitry is, etc. When the error code came on (a couple of days after cleaning and refilling), the water stopped running in the fountain? If the connection is good you would want to check your psi switch for blockage. Hot Tub Error Codes
This is located underneath the big hump on top of the pump motor. When the company opened Iit for the summer they blew the circuit board. This setting is not user-programmable.This condition does not kick in until the water temperature climbs to 95°F (35°C). weblink Contact dealer or a service technician if problem continues.OHOne of the sensors detected that the water in the hot tub is 112°F (44°C).
All Rights Reserved Send to Email Address Your Name Your Email Address Cancel Post was not sent - check your email addresses! How To Fix Flo Error Hot Tub Still same problem. Related Metals Robertshaw Controls Roper Products Saratoga Spas Savannah Spas Schrack Siemens Sonfarrel Spa and Pool Source Spa Builders Spa Components Spa Sanitation Inc.
If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa.
Remember, the cleanest spas have their filters replaced every 18-24 months. I don't know if you've tried this yet or not, but shut the spa down, remove any filters your spa has, then start the spa back up on low speed with Jet pumps 1 and the heater activate automatically to bring the temp to 15°F (8°C) of the settemps.Note: this condition often occurs when filling the spa with water since tap water Jacuzzi J 345 Fl1 Error The pump appears to be working fine.
Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Hot So I took the whole pump out and took it apart completely, motor and all!.. Tim July 19, 2016 Reply I have a sundance Hamilton 780. check over here If the control panel lights up with an SN1 or SN2 msg this might mean you have a bad temp sensor and or bad hi-limit sensor.
We attempted this roughly 5 times with no success. Check for Flow/Pressure Switch problem.FL2:Flow switch or pressure switch closed when pump is not running. I bought it used. It is also helpful sometimes to put your spa in economy mode to prevent overheating in the summer.
If you are good there, this is usually a good time to arrange for a service tech to come out. PLEASE AQUA-TECH SUPPORT Patty Dechellis April 13, 2014 Reply so should i turn the jets on?