Artesian Spa Error Code Dr
Thank you for a great post, it fixed mine as well! Spa will be shut down for 15 minutes. They can be removed and cleaned, and should be each time you drain your spa. I have done a lot of work and I am not able to see or find a blockage,,,, Derrick September 14, 2015 at 2:15 pm Thank you for taking the time navigate here
Dy: too little water in the heating element (this will appear after 3 x "dr" error) Follow the same steps as under DR. ICE = Freeze condition. 55°F detected. Drain and Refill the Spa Water per Manufacturers Instructions. Perhaps there is hair or debris caught in the impellar that is restricting the flow of water or possibly the motor is just defective. http://www.spadepot.com/spa-error-codes.htm
Hot Tub Error Codes
If you are in his area, call John. th2/current temperature = On startup indicates temperature probe problem. Turn the breaker to the spa OFF, and then cycle it back ON.
COOL = Spa water is more than 20° F cooler than the temperature set point. Kind Regards Karen admin June 27, 2012 at 9:57 am Hi Karen, I apologize my reply did not post before and I am not sure if you received my email. I'm stumped. Marquis Spa Error Codes drops.
This indicates a Problem with the Firmware (Operation Program), or the System is Operating on Unreleased Firmware (Sample or Prototype System). How To Fix Flo Error Hot Tub Either wait for the Potential Freeze Condition to End, or contact your Dealer or Service Organization. You could try jumping out the leads where the pressure switch/flo-sensors plug into the board and see if the heater will click on. http://www.troublefreepool.com/threads/86283-Spa-code-of-quot-Dr-quot-and-quot-Dry-quot-How-does-one-fix-this-issue-PLEAS-HELP!! A dry condition in the heater is dangerous and if left unchecked, the heater may start to sizzle and even cause a fire. Shut the spa off immediately if this is
This is a very common problem, and fortunately there are some simple solutions.Luckily, your spa may be smarter than a fifth grader. Artesian Spa Error Codes I had a mechanic come out and he was expensive and no help. I believe its not a air in line issue. SE = Spa operating in Standard-in-Economy Mode.
How To Fix Flo Error Hot Tub
Wait up to 1 minute to see if the error clears itself,if not reset the tub by turning off the GFI breaker, wait 1 minute, and then turn the breaker back http://en.allexperts.com/q/Hot-Tubs-3536/2008/6/Hot-Tub-dr-error.htm If you have a small circulation pump in your spa this could be clogged with debris and causing low flow. Hot Tub Error Codes Any idea? Vita Spa Error Codes I ordered a new flo switch, put filters back in to wait for new switch.
Your IP Address is: 184.108.40.206 Hot Tub & Spa Repair Spa Jets, Spa Parts, Spa Pumps, Spa Equipment, Hot Tub Jets, Hot Tub Parts, Hot Tub Equipment. http://msix.org/error-code/at-t-error-code-6.html FL2 = Pressure switch problem. Do not enter the water. It is to my knowledge that those error codes are telling me that there may be insufficient water supply to the heater but when I hand loosen the pipe fittings on Balboa Hot Tub Error Codes
dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). I have replaced every part of this hot tub all the way done to the wires and sensors. Test and Reset the G.F.C.I. http://msix.org/error-code/att-error-code-185.html Contact your Dealer or Service Organization.
System will restart when temp. Great Lakes Hot Tub Error Codes Quick View Register Help Remember Me? Back to Top Std, St, or STANDARD Message The Spa is Operating in the "Standard" (Std or St) Heating Mode.Between Filter Cycles, the Water Temperature is Sampled every 30 Minutes.
Replacing a Heater Element When exchanging a heater element, be sure to turn the power off and also the breaker. If the spa is drained it is easier to do a
If it has a seperate circ pump than maybe that is bad? -Jay Pam April 20, 2016 at 1:42 pm There is just one pump and it runs both speeds without Press "Mode" Button to Clear Message. In this condition, an attempt is made to trip the GFCI, which would shut off all power to the spa. Hydropool Hot Tub Error Codes And, were you able to solve the problem yet?
Read our FAQ! The Sensors are Possibly Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. What is a hot tub flow error? weblink Hot Tub Accessories Hot Tub Covers Footer links 2 Discount Hot Tubs Online FAQs Footer links 3 Disclaimer Hot news Winterize Hot Tub Our Newsletter Subscribe Unsubscribe c 2015 HotTubSpaTips.com ERROR
I ran a prime, 3 times and seems all the jets work and nothing is blocking any intake. Could it be that there is some dirt in the pipes causing this problem? Heat Related Pump Not Primed. I specialize in electrical questions and I am most familiar with spas that were manufactured by NEMCO, Regency, Hydro Spa, Gulfcoast Spas, Leisure Bay, and Premium Leisure.
These error codes are similar to the ones previous, however we will be looking at these at another angle. or Buy a replacement hot tub heater online in Canada here. If it is circulating on low speed and will not engage to high speed it could be the motor as well. pump is running and pulling water down through the filters.
This sometimes refreshes the pc board software if there is anything funky going on. If I am unavailable to answer your question here, you can check out my websites at http://sparepair.freeservers.com if you need troubleshooting help or if you need spa parts go to either Press any button to reset after the problem has been corrected, or or contact your Dealer or Service Organization. 1. Contact your Dealer or Service Organization.SnS or Sn is Blinking ON and OFF:There is a Verified "Sensors out of Sync" (SnS or Sn) with Each Other Condition.
Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or Continue for a Detailed Test Procedure.WARNING:A Heater Overheat Error Message may indicate Excessively High Heater Temperatures which Contact Info Precision Pool Construction 83 Haverhill Rd. We invite you to please Register to create a new account. One sensor has detected 118° F at heater.