Atm Errors Codes
Remove the remaining notes or foreign objects on the gate 2. Inspect the note transport make sure all belts are on track and there is no currency jammed in the transport or exit areas. Verify that version of Mini-Bank Software matches host processor. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. check over here
The width sensor may be dirty. W0004 The ATM time, as set in the Operator Function Menu, is incorrect WebRMS has detected that the ATM probably has incorrect date and time settings. Clear the error. Check state of notes in reject box 2. useful reference
Atm Error Code 3-da001
If problem persists, replace the device, cable or port 0G111 Poll time over Check the connection of the device cable, If problem persists, replace the device, cable or port 0G113 Response Complete several test dispenses. Seat connectors or replace the power supply as needed. 2.
- W0005 WebRMS coincidentally detected that the ATM was in Operator mode at the time the ATM was dialed into.
- On an 8 bit machine, such as 9100 or 9600, choose Diagnostics>More>More Keypad>Clear Tamper. 240 SPED Self Test Error The SPED has returned an error during self test. 1.
- If the error code continues, replace the note transport module.
- This error will not put the cash dispenser "Out of Service".
- If it is necessary to check continuity of the cable assembly,refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.
- Reconfigure cash dispenser setup data 9719700No.
- Loose belts can slip off rollers and block sensors. 24A15 CDU detects bills prior to dispensing This means that while the ATM was initializing it detected a blocked sensor in the
- Exchange sensor after abnormal operating CS13 Sensor 40043Error if total reject is more than 20 sheets1.
- Reinstall software 3.
Reconnect CS1 sensor 4004C00In case the number of notes detected outlet sensor(CS13) is more than that of notes detected on CS1A,B sensor 4004DError of being removed 1st cassette before separate rejection C0034 Double Note detect module failure Double detect module reporting error, check wiring to the module. Make sure all access panels are closed. Atm Error Code 3-da000(20) Set cassette #1 correctly 2.
Check notes in Reject Box 2. Atm Error Code 3-da000(80) Check Cash Dispenser EP ROM Version or specification 4003AWhen more than 5 sheets of cash dispensing is required during a test1. Other components that may cause this error are the main board or the dispensing mechanism. Recommended Action: See the recommended action for error code 144.
Check if the CS31 and CS31B Sensor Cable are disconnected 4. Atm Response Code 072 Check Cash Dispenser EP ROM Version or specification 4003A00When more than 5 sheets of cash dispensing is required during a test_ Check command that CDU is received _ Check CDU EP Clear all errors and perform several test dispenses. Baud rate set to high for telephone line conditions.
Atm Error Code 3-da000(80)
If the cash dispenser operates normally while performing a test dispense, put it back into service. https://www.nasatm.com/error_codes/code/D1800/ If error is persistent, modem may be defective D1300 NAK sent 3 times to host Verify host phone number - See D170x. Atm Error Code 3-da001 When performing a PURGE or TEST DISPENSE operation the return code will be "0" in the first digit returned by the dispenser. Hyosung Atm Error Codes Clear this error code by restarting the cash dispense or by unlocking and locking the cassettes.
If the cables are undamaged, the main board or electronic journal may be defective 162 Electronic Journal get serial number failed 1. check my blog Make sure they are not overfilled. Check the Cutter module 2. Error Code: 133 Description: +5 VDC not present on carrier detect. Sbi Atm Response Code 70
Replace hard disk drive 9719000Failed to execute an extra command in the status of Cash Unit Exchange1. D0080 Invalid Date Code reported by host processor. Vibrations can cause this error. 4. http://msix.org/atm-error/atm-error-codes-australia.html If these actions have no effect on dispenser operation, replace the dispenser mechanism.
Outside interference may cause it (neon signs, lights). Sbi Atm Response Code List Pdf C0033 CDU Encoder error Usually caused by loss of battery power to the CDU mainboard. Error Code: 319(43h)[C] Description: Jam in note transport.
Check for and clear any foreign matter the note path. 2.
Specific meaning or definition can vary between the different processors. Exchange a sensor after abnormal operating the CS37 sensor . 4009D00Trying to dispense bills from 3rd cassette but the 3rd cassette doesn't installed. 4009EMounting/demounting 3 Cassette during dispense operation1. Check communication cable 3. Atm Error Code 3-da000(60) Check the status of sensor and its connector 2080800Receipt paper cutting error1.
However, actions to fill the cassette should be taken as soon as possible. Inspect electronic journal to dispenser communication cable for damage. Please contact the manufacturer when this error happens. 0E233 Reset Default Error Software error. have a peek at these guys Initialize after resetting the power2.
Remove the remaining notes and foreign objects at the position of the CS 14 sensor 2. Make sure that all cables are securely fastened to their termination points. Results: No money is dispensed, screen and receipt display system unavailable Error Code: 4 Description: ERROR IN MODEM DATA Possible Cause: Unexpected data received from processor in response to message. Clear the error.
Change Cash Dispenser B/D 4003400Error of two sheets detecting sensor(CS5_1)for initializing1. Check if the CS31B and CS31B sensor cables are disconnected4. Reinitialize3. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error.