Atm Error Messages
Axxx2 Thermal printer is overheated - during operation If this error occurs during the printing of a long journal, then allow the printer to cool and try again. Reset the machine, if problem persist, please contact the manufacturer. 2G4C2 Head open error Close the printer header and press reset 2G4C3 Head Temperature Error Check Header 2G4C4 Cutting Error Parts Replace pinpad 9704020Failed to create file 9704021Failed to read file 9704022Failed to write file 9704023Failed to close file 9704024Failed to delete file 9704025Failed to copy file 9704030Failed to create Registry 9704031Failed D1900 No answer Verify host phone number - See D170x, there is no answer from the host modem.
Replace the Cash Dispenser B/D 4005500Timeout due to noteÕs length error passed through the CS13 during dispense operation1. Please contact the manufacturer when this error happens. 0E192 RX Over Run Software error. This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode). Close the lever of print head completely 2010200Receipt printer head overheated1. http://www.atmexperts.com/atm_error_codes.html
Atm Error Code 3-da001
Clear the error. Check if the CS3 sensor bracket is bended.4. Reset the machine if problems persist, please contact the service provider 43049 Please insert cassette Please insert Cassette 4304A S17 Jam Bill jam or sensor failure. Replace the dispensing mechanism. 56 Link error 1.
This occurs when the last cassette has been taken out of service. Remove notes on CS2 sensor 2. Verify that the diverter moves freely. Atm Response Code 072 Upgrade the Cash Dispenser firmware or download software again3.
It may be necessary to replace the dispenser. 201 Dispenser detected more than six errors in a dispense This status is generated when there are 6 rejects during the current dispense. Replace hard disk drive 9719100In case of not being the status of Cash Unit Exchange out of End Exchange1. Specific meaning or definition can vary between the different processors. Release the printer locking screw.
A mechanical error has occurred. Sbi Atm Response Code List Pdf W0006 WebRMS has failed to dial into the ATM consecutively for more than 3 days. Verify that all access panels are closed and secured. Replace the power supply or dispenser DC power if either is defective.3.
Atm Error Code 3-da000(80)
T0 Approval First check is OK and has been converted T1 Cannot Convert Check is OK but cannot be converted. https://stats.slimcd.com/documentation/Error%20Codes_full.htm If the problem persists, replace the dispensing mechanism. 135 Feed sensor blocked as reported by status check 1. Atm Error Code 3-da001 Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 104 Unable to clear width sensor. Hyosung Atm Error Codes Nautilus Hyosung ATM Machines, Triton ATM Machines, Hantle ATM Machines, and Genmega ATM Machines.
Vibrations can cause this error. 4. Reset the machine, if problems persist, please contact the manufacturer 5G129 Disconnect (ETX) Software error. Specific meaning or definition can vary between the different processors. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. 2. Sbi Atm Response Code 70
- Check the status of sensor and its connector 2080600Command is received while doing self-test1.
- If the test dispenses are completed normally, and the return code are correct, clear all errors and place the cash dispenser in operation.b.
- Purge the dispenser using the purge command.
- Check communication cable 3.
- If the error clears, put the cash dispenser in service. 3.
- If the error clears put the Cash Dispenser into service.
- Remove the remaining notes and foreign objects at the position of the CS21AB sensor 2.
- Clear the error.
- Remove the dust on the CS21A and CS21B Sensors5.
- If a belt displays excessive wear or damage you may be able to replace it.
Reset the cash dispenser. Call your attendant 9740101In case incorrect cassette type is set. 9740102In case nonexistent Note Index is set. 9741100When sensing CS2 Dark (Error code, 400FF00 is subdivided by location of sensor.) 9741400When Check for unplugged sensors. Remove a dust and foreign objects on CS11AB, CS21AB, CS31AB and CS41AB sensors.2.
Clear any jammed currency. 2. Ncr Atm Error Codes Check if CS62 sensor poll is abnormal3. Street address not verified because of incompatible formats. 1815-1896 not used 1897 invalid response The host returned an invalid response. 1898 disconnect The host unexpectedly disconnected. 1899 timeout Timeout waiting
R0 Stop Recurring Customer requested stop of specific recurring payments.
Check Cash Dispenser Firmware Version 40051Received a request for over 150 notes dispensing on the Cash Dispenser from the upper unit.1. D0050 Transaction is not approved Code reported by host processor (Shazam). Check if the CS62 sensor cable is disconnected (Cash Dispenser Board CN10 #5~2). 4005900Initial jam time error1. Atm Error Code 3-da000(20) Check CS8 Sensor Cable 6.
Check Main Motor Encoder Slit3. Replace hard disk drive 9719300In case of not being the status of Cash In out of End Cash In1. Clear all errors and test the dispenser with a live transaction. Please contact the services provider when this error happens. 0E255 GPIO default error Software error.
Remove the remaining notes and foreign objects at the position of the CS11AB sensor 2. If these actions have no effect, replace the dispenser. 51 Accountancy error A mechanical failure has occurred. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.