Atm Error Codes
Check serial number. 2. Initialize after resetting the power 2. Refill the cassette as needed. 2. Look for the bill jam very thoroughly. 4304C S23 error Bill jam or sensor failure. this content
Clean CS1A and CS13 40030Failed in checking the main motor echo1. Initialize after removing notes or dust over Gate. 2. Please contact the manufacturer when this error happens. 0E244 Watch Map Reset Base error Software error. Mount the retract box or open the box cover. 2. http://www.atmexperts.com/atm_error_codes.html
Atm Error Code 3-da001
This error will place the cash dispenser "Out of Service". Place all belts on their respective rollers and gears. NOTE: Do not use metal objects to clear the jam. Reboot ATM. 2.
- If the problem persists, replace the dispensing mechanism.
- Check if the CS37 sensor cable are disconnected (3 CST FM B/D CN3). 6.
- C0057 Cassette information is not properly set CDU programming is not accurate or complete.
- Wait the time until the temperature of head adequately slow down and try to initialize 2080300Receipt paper jam1.
Error Code: 111 (6Fh) Description: Diverter timeout Recommended Action: 1. Replace the dispenser is the error persists. If the error does not occur again, put the cash dispenser in service. Atm Error Code 3-da000(20) Remove note from the CDU delivery path. 2.
Check specifications of 4 Cassette FM Board Dip Switch (#3, #5, #6 On) 4005DContinuously detected 2 notes for three times or more during dispense operation1. Remove jammed notes. 2. Make sure that the cassettes are installed and locked before performing a test dispense or live transaction. Read More Here Clear the error.
Check for and clear any foreign matter the note path. 2. Atm Response Code 072 D011100 REVERSAL DECLINED D022200 PIN CHANGE DECLINED D100000 No connection 1. Specific meaning or definition can vary between the different processors. Remove a dust and foreign objects on the CS31AB or CS41AB sensors. 3.
Hyosung Atm Error Codes
Error Code: 119 (77h) Description: Diverter in dispense position on start of dispense or learn Recommended Action: 1. hop over to this website Check modem and modem cable connection. 2. Atm Error Code 3-da001 Check all wiring to mainboard. Atm Error Code 3-da000(80) Check Cash Dispenser Firmware Version 4005100Received a request for over 150 notes dispensing on the Cash Dispenser from the upper unit.1.
Remove note from the CDU delivery path. 2. Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Check the cable and connections from J7A on the docking station to the SPED board. 210 Dispenser type unknown See Error Code 130 236 Failed to make connection to TCP/IP host SDN0100 Service Panel (SPL) communication error Check the cables and connections. Sbi Atm Response Code 70
Exchange sensor after abnormal operating CS13 Sensor 40046Program error(Separated rejection)1. Suspect the main board, the TCP-IP connection device (Quad Port Board in 96XX, Docking board on RL, FT or RT) or the TCP-IP equipment. 237 TCP/IP device failed Out going commutations Error Code: 108 (6Ch) Description: Unexpected note at double detect Recommended Action: A note has been detected in the double detect sensor without being detected at the width sensor first. 1. http://msix.org/atm-error/atm-error-codes-australia.html Reposition the microswitch if necessary.
Check backup battery. Sbi Atm Response Code List Pdf Check the AP version and initialize 21A15CS1A sensor detects note in delivery path before CDU dispenses.Sensor is located along the delivery path right after where the note exits the 1st cassette.Remove Enter a smaller value.
Check Cash Dispenser Board Segment. 2.
D251100 Communication error while Sending Check telephone line connection. Check the abnormal communication cable. 3. Use an electrical parts contact cleaner on terminals. Sbi Atm Response Code 72 In line filter may help this.
Otherwise the printer needs service. Purge the dispenser using the purge command. 3. Check the AP version and initialize 2080AThe size of image print data is abnormal1. check my blog If the voltages are correct and the blue lever is in the print position, the most likely causes of the error are the printer, printer control board, or the main board.
Inspect for a currency jam at the diverter. 2. Reboot ATM. 2. Check transaction with the processor. Clear the jammed documents. 2.