Atm Error Code 3-d1500(00)
Check cabling and potential blockages and power cycle ATM. Test the dispenser by completing several test dispenses. 3. Error Code: 102 (66h) Description: Error (Pick Motor over current) Recommended Action: 1. Purge the dispenser using the purge command. this content
Got connected and never received ENQ within time-out period (14 Seconds). Recommended Action: This error code will be generated when the following conditions occur: 1. Other than upgrading the cash tray or using a sign to warn customers, you can loosen the screws that hold the dispenser and slide it back. A defective cassette may also cause this problem. https://www.nasatm.com/error_codes/code/D1500/
Atm Error Code 3-da001
Inspect the dispenser to make sure all belts are on track and in good physical condition. This problem may be caused by a corrupt pin working key. Clean the sensors a needed. 3. Clear any jammed currency. 2.
- Recommended Action: See recommended action for error code 138.
- Contact host processor D00A9 ETX omitted (from configuration message) Verify all programming.
- This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode).
- Reset the cash dispenser and clear the error.
- Inspect the dispensing mechanism for of damaged components or broken wires. 2.
- Replace the exit sensor if necessary. 4.
Make sure they are not overfilled. Place all belts on their rollers and gears. Other possible causes may be a defective modem or main board Error Code: 193 Description: The baud rate setting for electronic journal failed. Atm Error Code 3-da000(80) Remove any jammed notes. 2.
Error Code: 18 Description: OVERFLOW Possible Cause: Received more characters, than expected after request causing modem buffer overflow. Contact manufacturer.C007xSensor failureCheck sensors for debris. Verify that version of Mini-Bank Software matches host processor. Clear the error.
Otherwise try the reset button or have the printer serviced. Sbi Atm Response Code List Pdf If the error persists, replace the SPED keypad module. Reset the cash dispenser and clear the error. Error Code: 188 Description: PIN Working key not configured.
Atm Error Code 3-da000(20)
Inspect the feed path for any jammed notes. Remove jammed currency. 2. Atm Error Code 3-da001 Inspect all cables for damage. Hyosung Atm Error Codes Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error.
Set the cash cassette. news Error Code: 153 Description: Electronic journal mode. Reset the error. Clean the width sensor with compressed air. Sbi Atm Response Code 70
This will occur if the machine is switched off and on during normal daily operation. If the cash dispenser operates normally put it back in service. If two or more of the same type cassette are installed, inject a new cassette ID into one of the cassettes that is different from the other cassette. have a peek at these guys If these actions have no effect, replace the dispenser.
Error Code: 143 Description: PTDF (Processor Timeout Delay Failure) - ACS Code only. Atm Error Code 3-da000(60) Clear terminal error code. If a cassette is not responding it may be necessary to inject a new identity into the cassette by completing the inject new cassette ID command.
If the error clears, put the cash dispenser back in service.
Open the access panels on the note transport and remove any documents that may be in the transport path. D2000 Phone line Busy Verify host phone number - call line with handset and check for busy signal - See D170x. Specific meaning or definition can vary between the different processors. Ncr Atm Error Codes Error Code: 359 Description: Dispenser device record error.
C009F 3Cassette misfeed error Check if notes available in cassette C00AB Notes detected before initalizing Clear notes from dispenser. Error Code: 140 Description: Time-out waiting for printer to be ready. C005A Cash cassette 1 removed prior to dispense Set the cash cassette. check my blog Check and reseat all belts.
Restart the operating system. ADN0F Printer connection error Check cables between Printer and Mainboard, remove cables (even though they may be attached) and re-connect. C0037 Sensor(NS7) for detecting Double is covered during dispensing note Check cable running to sensors and make sure they are securely placed. Both sensors must be blocked for this error to occur.
Error Code: 362 Description: Dispenser device write error. Complete several live dispenses to ensure the dispenser is working correctly. Recommended Action: This error may occur anytime that a cassette is removed from the cash dispenser with the AC Power ON. Error Code: 55 (37h) Description: RAM corruption Recommended Action: A mechanical failure has occurred.
Check the cable and connections from the docking station to the SPED board. C0034 Double Note detect module failure Double detect module reporting error, check wiring to the module. Otherwise, replace the dispenser.