An Error Occurred During Port Configuration Windows 8
I even tried using Print Management service. All rights reserved. By analyzing and understanding these TTPs, you can dramatically enhance your security program. Required fields are marked *Comment Name * Email * Website Notify me of followup comments via e-mail. http://msix.org/an-error/an-error-occurred-while-windows-was-synchronizing-with.html
Let me know what errors you receive?HP Utilities -------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- Reply 0 0 Leila1939 Intern Posts: 18 Member I also removed Network Magic from both PCs; then I used the 'view-workgroup-computers' technique that you suggested. Even my Network Admin could not figure it out… Saved me a lot of trouble…Thanks again. If your specific printer isn't shown, you can click on Have Disk and browse to the folder where you have the unpacked drivers for your printer.
An Error Occurred During Port Configuration This Operation Is Not Supported Windows 7
Windows 10 Windows 8 Windows Server 2012 Windows Server 2008 Windows 7 OS Security How to Fix Bootloader Problem for Windows 10 Article by: Jackie When you start your Windows 10 What printer brand and model are you trying to install ?Thank you Ask Your Own Computer Question Customer: replied6 years ago. In fact, the solution was far simpler - but also slightly strange… It turns out that Windows Vista automatically enables SNMP support for networked printers, and if it can't get a The list looks just like the Windows Add Hardware Dialog.
Try uninstalling and reinstalling the printer. Worked fine. I had port 192.168.0.1, unchecked SNMP but apply was greyed out and OK didn't do the job. Configure Port Operation Not Supported Windows 10 This was specific to an issue with Windows Server 2008 and a TCP/IP printer.
It worked immediately. It may be correct, and I have a printer connected directly to my router, so I can't check to make sure, but I think it should be a "Standard TCP/IP port." I almost went nuts over this but you saved me!!! http://www.tomshardware.com/forum/242724-44-port-configuration-operation-supported Thank you!)2- Let me know if the answer doesn't work INSTEAD of leaving negative feedback, so we can still continue troubleshooting the issue.3- Positive Feedback is very important to us.
Not installing a printer, just can't print all of a sudden, I have the printer attached to a USB port and when I try to configure the port I get the Configure Port Not Supported Windows 10 This will be demonstrated using Windows 7 operating system. Tech Support Guy is completely free -- paid for by advertisers and donations. Access is denied." What do I do now?
An Error Occurred During Port Configuration This Operation Is Not Supported Windows 10
I don’t know why they made the change, but we’ll just have to improvise, adapt, and overcome. Please leave me a positive feedback after you are happy with the answer.4- Any bonus will be greatly appreciated Ask Your Own Computer Question Customer: replied6 years ago. An Error Occurred During Port Configuration This Operation Is Not Supported Windows 7 I've been suggesting unplugging the printer, removing all the software for it, then re-installing. Windows 10 An Error Occurred During Port Configuration Thank you!
solved Router ports Configuration solved "Supported Memory Configurations" solved Will my motherboard or configuration support Windows 7? this contact form Microsoft Chat/Epson Chat, no one can help. Reply Carys Edwards says: September 7, 2016 at 15:27 It still does not work !! If you get an error message please let me know)5- Replug the printer and try to print6- Please let me know if the issue is solved or not, so we can An Error Occurred During Port Configuration Operation Could Not Be Completed
Please leave me a positive feedback after you are happy with the answer.4- Any bonus will be greatly appreciated Ask Your Own Computer Question Customer: replied6 years ago. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. replied6 years ago. http://msix.org/an-error/an-error-has-occurred-you-have-been-signed.html Cheers Jay Earl J.
JohnWill, Jun 24, 2009 #8 concordal Thread Starter Joined: Jun 22, 2009 Messages: 5 Resolved! An Error Occurred During Port Configuration Access Is Denied ED KIM says: July 22, 2014 at 9:45 pm When I tried this, I received the message "An error occurred during port configuration. Windows 7 Advertise Here 708 members asked questions and received personalized solutions in the past 7 days.
Access is Denied.” Marcel says: May 18, 2015 at 05:45 Thanks!
- Dade says: February 22, 2015 at 9:02 pm This worked on Windows 7 Pro.
- Leave a Reply Cancel reply Name (required) Mail (will not be published) (required) Website KW Recent Blog Change your Yahoo Password Now!
- First Name Please enter a first name Last Name Please enter a last name Email We will never share this with anyone.
- Credentials confirmed by a Fortune 500 verification firm.
- Reply MikeScott says: December 2, 2015 at 11:16 No problem, I'm glad it helped!
- Untick that, and the printer should start showing as online again.
- Viplove says: November 5, 2014 at 12:49 am Thanks a ton !!!
- Jay Young says: August 19, 2014 at 5:01 pm Hi Robin, I've been trawling through the net all day.
- Wendy Yap says: March 30, 2015 at 8:21 am Thank you so much !!
Thanks for the feedback and your solution. I could print only each time I was restarting my computer… Thanks for the help! Thanks Reply Leave a Reply Cancel reply Your email address will not be published. An Error Occurred During Port Configuration The Requested Resource Is In Use Zac Durst says: January 28, 2015 at 1:54 pm Wow, Thanks!
When you highlight the port for this printer, I get "filename, directory name or volume label syntax is incorrect.Can anyone help me with is>? No problem!After clicking Control Panel, then click "View By: Category" then click "Uninstall a program" under "Programs"Then please continue with steps 3 to 8Thank you! It gets stuck in the Queue and I have to delete it before proceeding, Everything I try gets stuck in the Queue Expert: Engineer John C. Check This Out Simply right-click on the printer in the Printers window, choose the Ports tab, and select Configure Port.
Just select your port and click “Configure Port” and you’ll have access to everything you expected. Access is Denied.Archives September 2016 August 2016 May 2016 November 2015 September 2015 June 2015 October 2014 September 2014 May 2014 April 2014 Categories Agents-of-shield AverageUsers Books CyberSecurity Development Diablo-iii-Reaper-of-Souls Errors Robin Wilson says: July 23, 2014 at 7:23 am It sounds like it could be a permissions problem.